Can you hook up 2 washers together?
You can run both washers simultaneously as they fill until a sensor or float says the water level has risen to the set-point. It will just take a bit longer for them to fill if you run them at the same time.
Why does my washer have two drain hoses?
What is the purpose of two drain connections? LAW is a water saver, can drain the soapy water into a tub and th esecond hose drains the rince water down the drain…the soapy water can be drain back into the machine to be used a second time.
Can a washing machine share a drain?
The plumbing code requires one on every drain and has established rules governing its size and distance from the fixture trap. If you’re joining a washing machine and kitchen sink on the same drain, you may be able to vent them both with a single vent if they are close enough together.
Can two washing machines drain one?
You can’t leave a direct connection to the main stack open. You would be best served by using a deep laundry sink to accept the waste from the two washing machines and let the sink drain through a proper trap arrangement.
Is it OK to extend washing machine drain hose?
If a remodeling project forces you to move the washing machine too far from the drain and the water supply for the hoses to reach, you don’t have to relocate the plumbing. Lengthening the drain hose isn’t difficult, because you can buy a drain hose extension that simply clamps onto the end of your existing hose.
Can I stack 2 washing machines?
Many homeowners assume that any two laundry appliances can be stacked together, but unfortunately this is not the case. While there will be some interchangeability in washer and dryer models across the same brand, you will not be able to stack laundry units from two different brands.
Why would you use two washers?
The large washer has a lot of friction against the bed post, so the bolt does not turn and back out. Also having the larger washer next to the frame spreads out the force on the frame which is usually softer and thinner than the bolt head.
Why does my Maytag washer have two drain hoses?
The machine will also have two drain hoses. One is the regular drain hose, the other the suds saver hose. When “Save Suds” is pushed, at the end of the wash portion of the cycle, the machine will divert the drained soapy water into the suds saver hose.
How do you hook up a washer and washing machine to the same drain?
Connect the Sink and Washing Machine
- Insert the drain hose from the washing machine into the top of the sewer pipe.
- Fit together the p-trap and drainpipe and place them into position between the tailpiece and the sewer pipe.
- Connect the drainpipe for the sink to the tee inlet.
Can a washing machine drain into 1 1 2 pipe?
Drain and Trap Requirements A 2-inch drain pipe is required for all washing machines. The former requirement of 1 1/2-inch pipe is not enough to handle the fast drainage of modern washers. As with all plumbing fixtures and appliances, a washing machine drain pipe must also contain a P-trap.
How do you attach a washer drain hose to a washing machine?
If the drain hose is attached to the top back of the machine, loosely attach the hose across the back of the machine horizontally if the floor drain is on the opposite side of where the drain line attaches to the rear of the washer. Install a washer drain hose siphon break above the 28-inch mark on the back of the washer.
What size pipe do I need for a washing machine drain?
2-inch pipe for washing machine drain; Standpipe 24 inches above p-trap; Branch arm to vertical stack; Relax, I’m a master plumber; CLICK HERE to Get Tim’s. Washing Machine P Trap And Drain – Plumbing – DIY Home Improvement.
Where does the drain hose go on a Kenmore Elite washer?
If the drain hose is attached to the top back of the machine, loosely attach the hose across the back of the machine horizontally if the floor drain is on the opposite side of where the drain line attaches to the rear of the washer. Get the Best Mortgage Rate for You
How do you install a siphon break on a whirlpool washing machine?
Install a washer drain hose siphon break above the 28-inch mark on the back of the washer. Cut through the drain hose above the 28-inch mark with utility shears. Insert the two plastic drain hose sleeves provided with the siphon break kit into the cut ends of the hose. Slip the kit’s hose clamps over the cut ends.