How long is a Dana 44 rear axle?

How long is a Dana 44 rear axle?

In all applications, the Dana 44 is a semi floating axle with either an 8.5 or 8.9 inch ring gear. The 8.9 inch ring gear Dana 44 is a stronger and favorable design used in the Jeep JK (2007 – current), Nissan Titan, and some Isuzu pickups.

What size is a Dana 44?

Ring gear diameter is 8.5 inches, while next-generation axles go up to 8.8 inches. The available gear spreads for the Dana 44 range from 2.72:1 to 5.89:1, and both five- and six-lug versions were used in OE applications.

How wide are Dana 44 axles?

At 60 3/4 inches wide, this axle is almost the same width as a TJ (61 1/2 inches, wheel-mounting surface to wheel-mounting surface). They are commonly found with Trac-Lok limited slips and either 4.30 or 4.56 gears.

Is Dana 44 strong?

It used to be that the Dana 44 was considered to be a fairly stout axle. But as trails got tougher and tires got larger, the 44 got dumped in favor of even stronger hardware. But the Dana 44 is a pretty stout piece, and many companies offer parts to make your 44 even stronger than it now is.

What size are the axle tubes on a Dana 44?

2.5 to 3-inch
The Dana 44 came with axle tubes anywhere from 2.5 to 3-inch in diameter.

Is a Dana 44 a good axle?

At the same time, the Dana 44 is a great axle if you don’t need giant tires or big power. Most people don’t realize how heavy a Dana 60 is and how much unsprung weight affects handling. The Dana 44 is also a heavy axle, but it’s significantly lighter than a Dana 60.

What front Dana 44 will fit a TJ?

Well, the JK Rubicon Dana 44 front and rear axles offer a number of upgrades over the TJ Rubicon Dana 44 axles. The rear JK Rubicon Dana 44 bests the TJ Rubicon Dana 44 in pinion diameter, axleshaft spline count, and axletube diameter.

What is axle length?

TRACK LENGTH: measure your axle track length by determining the distance between the center of one tire to the center of the other tire. A more precise measurement can be made by measuring the distance from one ‘HUB FACE’ to the other.

Can a Dana 44 handle 40s?

For a daily driver or a non wheeling rig, 44 and 40’s are fine.

Can you run 40 inch tires on a Dana 44?

However, as a very general rule, a 36-inch tire is about the limit for a Dana 44. Of course, we all know the guy that runs 40-inch tires on his Dana 44 and never breaks a thing. But if you drive like a grandma in a lightweight rig with a stock powerplant, you might be able to run a tire bigger than 36 inches.

What size is a Dana 44 axle?

The Dana 44 came with axle tubes anywhere from 2.5 to 3-inch in diameter. The Dana 60 only came with one axle diameter of 3.125 inches, which is pretty big. Those larger axle tubes help strengthen the housing, but also make room for larger axle shafts.

What is the diameter of a Dana 44 axle tube?

Dana 44 axle tube diameter ranges from 2.5″ to 3″, while the Dana 60 axle tube diameter is 3.125″. So, while the Dana 60 has a stronger housing than the Dana 44, it’s not by a massive amount, especially for the larger Dana 44s.

What vehicles have a Dana 44 rear?

ZJ Grand Cherokees with the V8 engine have a Dana 44 rear end, and some of the 4.0-liter ZJ with a tow package do too. For TJ Wranglers it was a factory option if you got the 4.0-liter engine.

What is a Dana 44 front axle?

The Dana/Spicer Model 44 is an automotive axle manufactured by Dana Holding Corporation and is used extensively among automobile manufacturers and in the automotive aftermarket area as well. The Dana 44 was first manufactured in the 1940s and is still being manufactured today, both front and rear axle variants.