How much does it cost to replace a heating element in a Whirlpool dryer?
A new heating element is usually between $40 and $100. This part might cost as low as $30 and as high as $200 or more, depending on the type of dryer.
Is it worth replacing heating element in dryer?
If your dryer’s heating element burns out more than once within a year or two, the thermal fuse, which is supposed to protect it, is probably defective, so it’s a good idea to replace it. The temperature in the heating chamber may also be too high, and that may be caused by poor venting.
How long should a dryer heating element last?
between 8 and 18 years
The heating element can last between 8 and 18 years if the dryer is well-maintained and the vent and lint traps are clean. The heating element can burn out if the dryer is not kept well-maintained.
What causes a dryer element to burn out?
A dryer’s heating element operates on the same principle as the coil in an electric heater. It consists of an uninsulated metal conductor and when an electric current passes through it, its resistance to the flow of electricity makes it heat up. If the coil gets too hot, it burns out.
How long do Whirlpool dryers last?
about 13 years
The average dryer lasts about 13 years. The average residential dryer will last 13 years.
How can you tell if a dryer heating element is bad?
Inspect the metal wire coil for any breaks in the wire. If the wire is solid and has no breaks in it, the heating element should be good. If the wire has a break in it, the heating element is defective.
What would cause a whirlpool dryer not to heat?
When gas or electric Whirlpool Dryer is not heating up, it usually caused by: Burnt Heating Element or Gas Valve Solenoid, Burnt Thermal Cut-Off Fuse, Defective Cycling Thermostat Or Gas Ignitor, Malfunctioned Flame Sensor.
What is wrong with my dryer it doesn’t get hot?
Common reasons for an electric or gas dryer not heating are a tripped circuit breaker, clogged vent, and no gas flow. Other potential reasons include a faulty thermal fuse and broken heating element.
Do dryer heating elements go bad?
Bottom Line. If the dryer is well-maintained and the vents and lint traps are kept clean, the heating element can last between 8 and 18 years. If the dryer is used on a daily basis and is not kept well-maintained, the heating element can burn out at any time.
How long should a dryer element last?
How do you change the heating element in a dryer?
Steps Unplug the dryer. Take off dryer exhaust hose and remove the back panel. Look at the back of the dryer. Unscrew the black sensor on top, and unscrew the black sensor on the bottom. Unhook the two wires just below the bottom sensor. Gently lift up on the whole gray casing. Turn it upside down; you’ll see one screw holding the element in.
Where is the heating element on a whirlpool duet dryer?
Dryer heating element 279838-R is used on Whirlpool, Roper, Estate, Kenmore and some other brand dryers. The heating element is typically located near or attached to the bulkhead of the dryer.
How do you clean a whirlpool duet dryer?
How to Clean Whirlpool Gas Dryer Vents & Lint Traps. Remove the screws securing the round, metal vent from the back of the dryer, using a nut driver or screwdriver. Pull the vent off of the dryer vent outlet. Insert the dryer lint brush into the vent as far as it will go. Move the brush around and from side-to-side. Pull the brush out. Do this several times until there is no more lint on the brush.
What is the heating element of a dryer?
The heating element is a metal chamber containing a coil of heating wire used to generate heat in an electric dryer. A gas dryer uses a gas heater controlled by a shutter that serves the same function as an electric heating element. Dryer heating elements contain a coiled wire made from a chrome and nickel alloy.